Bryant Furnace Repair | Error Codes, Troubleshooting & More (2024)

FAQs

How do I read my Bryant furnace error code? ›

You can view the error code LED or display through a small, clear plastic inspection port in the centre of the lower furnace cover. If the control board isn't in the lower compartment, it's in the upper compartment.

An error with the gas, ignition failure, or flame can cause the red light to start blinking. This could be an indication that your flame sensor is dirty, and/or could also mean there is a problem with the gas valve or ignitors.

They are located just outside the burner chamber. Turn off the power then press the small button between the 2 leads to reset it. If it clicks you have reset it and the unit will fire up when you turn the power back on with any luck. If it doesn't click it wasn't tripped.

To check for blinking diagnostic error codes, you'll need to locate your furnace's control board. This is usually behind a removable panel. There will be a small LED display with a light that blinks on and off in a set pattern. Count the short and long blinks related to a specific code.

Soliod red just means it has power. If furnace fails we get a 2 digit code by number of long and short flashes.

Typically, your furnace light is a solid amber or yellow color, which tells you everything's good inside the furnace. Blinking red light means something's not right. The trouble can range from an easy fix, like a tripped breaker switch, to something more serious, like a problem with the gas valve.

A blinking red light may indicate that your thermostat is not sending a signal to the furnace. This could be due to faulty wiring within your walls or a loose wire connection. Solution: Check all connections and ensure they are secure. If the wiring appears to be in good condition, consider replacing your thermostat.

A yellow blinking light on your furnace can indicate a specific issue with your heating system. While the exact meaning may vary depending on your furnace model and manufacturer, a common interpretation is that it signifies a need for attention or maintenance.

7 flashes. Lockout due to no ignition. Faulty or dirty flame sensor, faulty igniter, dirty filter, etc.

If your furnace doesn't have any air coming out at all and the pilot light is out, it's worth it to try resetting the furnace. If this doesn't work, there may be a problem with the thermostat setting, the power, or the gas line.

Is it safe to hit the reset button on a furnace? ›

The button will pop out if your furnace gets too hot or experiences an electrical interruption. If you need to reset your furnace, press the button for 30 seconds only once. Pressing the button several times will engage the safety lock and may even damage the unit.

The 5 flash code represents an open rollout switch that will most likely have to be reset with the small red button on the back. The switch should be located near the burner to be able to sense the flame rollout. This is what it should look like: Ask Your Own HVAC Question.

The four red flashes mean a high limit switch or 24-volt fuse is open. A malfunctioning blower motor, a clogged air filter, a defective ducting system, an open fuse on the control board, or limited circulating air circulation are just a few of the potential causes.

defective switch or connections; improper minimum- or maximum-heat gas input adjustment; dirty filter or restricted duct system; improper limit switch.

The serial number is formatted by 4 numbers, a letter, then 5 numbers. The first two numbers are the week of manufacture and the following two numbers are the year of manufacture. The date of manufacture can usually be found on these units.

The serial number is made up of a letter followed by a nine-digit number. The second and third letters represent the year; the fourth and fifth numbers represent the week. There may be a date stamp to the right of the serial number. The first six digits are the Unit Identity Number.

The first three digits, that is G26 in the above example can tell us about the series number of the product. G here stands for Gas and 26 means 26th unit produced in the lot. Unit capacity or Size. The next three digits, that is Q3/4 can tell you about the capacity and size of your furnace unit.